Product Details
Technical Specifications
| Feature | Specification |
|---|---|
| Nominal Diameter | DN15 – DN600 (1/2″ – 24″) |
| Pressure Rating | PN16~PN420 / ANSI Class 150~ 2500 |
| Flow Characteristics | Equal Percentage, Linear, Quick-Opening |
| Leakage Class | ANSI Class IV, V (Standard) / Class VI (Soft Seal) |
| Temperature Range | Long extended bonnet: -100°C to -196°C |
| End Connections | Flanged (RF, RTJ), Butt-Weld (BW) |
| Supply Air Pressure | 0.14 – 0.40 MPa |
FAQ
Q1: What defines a cryogenic control valve, and how does it differ from a standard control valve?
A: A cryogenic control valve is specifically engineered for media temperatures below -40°C, with some designs rated down to -196°C (liquid nitrogen) or even -253°C (liquid hydrogen). The key differences from a standard valve include:
Extended Bonnet (Cold Box): An elongated stem section that positions the packing box and actuator far enough from the cold media to keep them above their minimum operating temperature.
Low-Temperature Packing: Specialized packing materials (PTFE or graphite compounds) that remain flexible and seal effectively at cryogenic temperatures.
Material Selection: Austenitic stainless steels (CF8/CF8M, F304/F316) or nickel alloys that retain toughness at low temperatures, avoiding ferritic steels that become brittle.
Q2: At what temperature must I specify a cryogenic extended bonnet?
A: The general threshold is -40°C. Below this temperature, standard valve designs cannot guarantee packing seal integrity or actuator performance. The required bonnet extension length depends on the media temperature:
-40°C to -100°C: Standard extended bonnet (short neck).
-100°C to -196°C: Long extended bonnet (for LNG, liquid oxygen, liquid nitrogen service).
Below -196°C: Extra-long extended bonnet with specialized insulation (for liquid hydrogen or liquid helium service).
The purpose of the extension is identical to a high-temperature bonnet — keep the packing and actuator at safe temperatures — but in reverse: instead of dissipating heat away from the packing, it keeps ambient heat from reaching the cold media while protecting the actuator from freezing.
Q3: What materials are suitable for cryogenic valve internals?
A: Material selection is critical at low temperatures because many metals undergo a ductile-to-brittle transition:
Austenitic Stainless Steel: CF8 (304), CF8M (316), F304, F316 — the most common choice, retaining full toughness down to -196°C.
Nickel Alloys: Monel, Inconel, Hastelloy — for extremely low temperatures or corrosive cryogenic media.
Brass/Bronze: Acceptable for moderate low-temperature service (down to -40°C) in non-critical applications.
Avoid: Carbon steel, ferritic stainless steel (F6A, CA15), and cast iron — these become brittle and may fracture without warning at cryogenic temperatures.
Q4: What is the maximum operating temperature for this valve?
A: -40°C to -100°C: PTFE V-ring packing — remains flexible and provides excellent sealing at moderate cryogenic temperatures.
-100°C to -196°C: Low-temperature PTFE or PCTFE (polychlorotrifluoroethylene) — specially formulated to resist cold flow and maintain seal integrity.
Below -196°C: Specialized cryogenic graphite or PCTFE compounds with anti-extrusion rings.
Important: Standard PTFE may cold-flow (creep) at very low temperatures, causing packing relaxation and leakage. Always specify cryogenic-grade packing for temperatures below -100°C, and ensure the packing is installed with proper anti-extrusion rings to prevent cold media from migrating up the stem.
Q5: Are there special installation requirements for cryogenic control valves?
A: Yes, cryogenic installation demands strict adherence to several requirements:
Vertical Installation: The valve must be installed with the stem vertical and actuator on top. This ensures the cold liquid stays in the valve body and does not migrate into the packing box or actuator.
Pre-Cooling (Cooldown): Before putting the valve into full service, the valve must be gradually pre-cooled by slowly introducing cold media to avoid thermal shock. Rapid cooling can cause thermal stress cracks in the body or trim.
Insulation: The valve body and extended bonnet neck must be insulated with closed-cell foam or vacuum-jacketed insulation to prevent ice buildup and moisture ingress. However, the packing box area must remain accessible for maintenance.
Q6: What are the key maintenance considerations for cryogenic valves?
A: Cryogenic service requires a proactive maintenance approach:
Packing Inspection: Check for frost or ice formation around the packing box — this indicates packing leakage allowing cold media to escape and atmospheric moisture to freeze. Re-tighten or replace packing as needed.
Stem Condition: Inspect the stem for pitting, scoring, or ice buildup that could cause sticking. Cryogenic service can cause moisture ingress that freezes on the stem surface.
Bonnet Insulation Integrity: Verify that the insulation jacket on the extended bonnet is intact and free of moisture. Damaged insulation leads to ice accumulation and increased operating torque.
Leak Testing: Perform helium leak testing (not just bubble testing) on cryogenic valves during commissioning and periodic maintenance, as standard soap solution tests are unreliable at low temperatures.
Actuator Function: Verify full stroke and response time after each cooldown cycle, as thermal contraction can affect linkage clearances and spring preload.
Q7: What are the common faults and troubleshooting steps for cryogenic control valves?
A: The most frequently encountered issues in cryogenic service include:
External Frost/Ice at Packing Box: Indicates packing leakage. Solution: Re-tighten gland follower or replace with cryogenic-grade packing and anti-extrusion rings.
Valve Sticking After Shutdown: Caused by ice formation on stem or moisture ingress into the bonnet. Solution: Purge with dry nitrogen, inspect stem for damage, and verify insulation integrity.
Excessive Operating Torque: Often due to ice buildup in the guide mechanism or thermal contraction reducing clearances. Solution: Clean and re-lubricate with cryogenic-compatible lubricant, verify guide bushing clearance.
Internal Leakage at Low Temperature: Thermal contraction can change the fit between plug and seat. Solution: Ensure trim materials have matching thermal expansion coefficients, and verify seat alignment after cooldown.
Actuator Slow Response: Caused by moisture freezing in the air supply lines or positioner. Solution: Install air dryer and heat tracing on instrument air supply, use cold-weather positioner rated for low ambient temperatures.
Our Certificates










