Pneumatic Three-Way Control Valve

Technical Specifications Feature Specification Nominal Diameter DN15 – DN600 (1/2″ – 24″) Pressure Rating PN16~PN420 / ANSI Class 150~ 2500 Flow Characteristics Equal Percentage, Linear, Quick-Opening […]

Product Details

Technical Specifications

Feature Specification
Nominal Diameter DN15 – DN600 (1/2″ – 24″)
Pressure Rating PN16~PN420 / ANSI Class 150~ 2500
Flow Characteristics Equal Percentage, Linear, Quick-Opening
Leakage Class ANSI Class IV, V (Standard) / Class VI (Soft Seal)
Temperature Range Standard: -20°C to 200°C / Extended Bonnet: -60°C to 450°C
End Connections Flanged (RF, RTJ), Butt-Weld (BW)
Supply Air Pressure 0.14 – 0.40 MPa

 

FAQ

Q1: What is the main advantage of using a three-way control valve instead of two two-way valves?

A: The core advantage is simplified piping layout and stable total system flow. A single three-way valve can replace two single-seated two-way valves plus a three-way pipe fitting, saving installation space, reducing material costs, and eliminating potential leak points from extra connections. During modulation, the total flow resistance of the system remains nearly constant, avoiding flow fluctuations that occur when using two separate two-way valves operating in parallel.

Q2: How do I choose between a mixing (converging) and diverting (splitting) three-way valve?

A: The choice depends on your process flow path:

  • Mixing valve (2 inlets, 1 outlet): Used to blend two fluid streams (e.g., hot + cold water) to achieve a target outlet temperature. Commonly installed downstream of heat exchangers.
  • Diverting valve (1 inlet, 2 outlets): Used to split a single fluid stream into two paths (e.g., routing part of a flow through a heat exchanger and part through a bypass). Commonly installed upstream of heat exchangers.

Note: For DN≤80, a mixing valve can be used as a diverting valve in non-critical applications, but for larger sizes, a dedicated diverting valve is required. You can identify the valve type by checking the flow arrows on the valve body (two arrows pointing inward = mixing; one arrow pointing inward, two outward = diverting) or the nameplate label.

Q3: Can this valve handle media with large temperature differences or high pressure drops?

A: For standard configurations, the temperature difference between the two inlet streams of a mixing valve should not exceed 150°C (some manufacturers specify a limit of ≤120°C) to avoid thermal stress on the valve internals. For high-temperature or high-pressure-drop applications, we offer optional hardened trims (Stellite overlay on the plug and seat) and anti-cavitation cages to reduce wear and noise. The standard leakage rating is ANSI Class IV (≤0.01% of rated Cv), with optional Class VI soft-seal versions for tight shut-off requirements.

Q4: What is the operating temperature range for this valve?

A: The temperature range depends on the bonnet design and packing material:

  • Standard bonnet: Suitable for media temperatures from -20°C to 200°C (PTFE packing).
  • Extended bonnet with cooling fins: For high-temperature steam or thermal oil applications, handles temperatures up to 450°C (graphite packing).
  • Cryogenic bonnet with isolation plate: Designed for low-temperature media down to -196°C (extended stem to protect the actuator from cold damage).
Q5: What flow characteristic should I select for this three-way valve?

A: We offer two standard flow characteristics:

  • Linear: Best for level or flow control loops where the process gain is relatively constant, such as simple flow distribution or bypass regulation.
  • Equal percentage: Ideal for temperature control systems, as it provides finer adjustment at small openings to compensate for the non-linear heat transfer characteristics of heat exchangers.
Q6: What maintenance and installation requirements does this valve have?

A: The valve must be installed with the stem in a vertical position; horizontal installation will increase packing leakage by up to 3 times due to uneven wear on the plug guide. Routine maintenance includes inspecting the stem packing for leaks, checking the actuator diaphragm for cracks, and verifying the positioner calibration. Thanks to the top-guided modular design, the valve internals (plug, seat, cage) can be removed and replaced without taking the valve body out of the pipeline, minimizing downtime.

Our Certificates

Project Cases

YOSUN Automation
YOSUN Automation
YOSUN Automation
YOSUN Automation
YOSUN Automation
YOSUN Automation
YOSUN Automation
YOSUN Automation
YOSUN Automation
YOSUN Automation

Get a Quote

    ✕

    Get a Quote